View FH34SJ-30S-05SH50_6946830.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 features 1. low-profile with the 1.0 mm above the board and width of 3.8 mm the connectors are used in space saving applications. 2. increased fpc/ffc retention as compared with existing similar construction connectors: * in horizontal direction: approximately 2.6 times * in vertical direction: approximately 2 times 3. unique back-flip rotating actuator the rotating actuator opens from the back of the connector, assuring reliable electrical and mechanical connection. 4. easy fpc insertion and reliable electrical connection proven flip lock actuator allows easy insertion of fpc and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. delivered with the actuator open fpc/fpc can be immediately inserted without the need for the opening of the actuator. 6. accepts standard fpc thickness 0.3mm thick standard flexible printed circuit (fpc) can be used. this is the only ultra-low profile zif connector using standard fpc. 7. compatible with existing connectors. fpc/ffc and pcb mounting patterns are the same as for the fh19sc series (bottom contact), allowing the use of both connectors for interconnections between two boards or replacement of the connectors. 8. conductive traces on the pcb can run under the connector no exposed contacts on the bottom of the connector. 9. board placement with automatic equipment flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. standard reel packaging contains 5000 connectors. 10.halogen-free * (fh34sj,fh34sw,fh34srj) *as defined by iec61249-2-21 br-900ppm maximum, cl-900ppm maximum, cl + br combined-1,500ppm maximum 2012.3 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors fh34(s)series increased fpc/ffc holding force compatible with existing connectors.(fh19sc series) 1.0mm 3.2mm 17mm metal fittings actuator easy fpc/ffc insertion 17mm fpc / ffc back opening rotating top contacts all four sides are chamfered. ready to insert fpc/ffc fpc/ffc inserted and retained. completed electrical and mechanical connection. delivered with the actuator open delivered with the actuator open fpc fpc space saving (30 pos. shown)
fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 2 specifications ratings current rating 0.5 a (note 1) voltage rating 50 vrms ac operating temperature range: -55 to +85c (note 1) operating humidity range: relative humidity 90% max. (no condensation) storage temperature range: -10 to +50c (note 2) storage humidity range: relative humidity 90% max. (no condensation) recommended fpc/ffc thickness: 0.3 0.03 mm, gold plated contact pads item specification conditions 100 v dc 250 vrms ac / one minute 1 ma, ac / dc 20mv max (ac: 1khz) 20 cycles frequency: 10 to 55 hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 axis acceleration of 981m/s 2 , 6 ms duration, sine half- wave, 3 cycles in each of the 3 axis 96 hours at 40c and humidity of 90 to 95% temperature : -55c / +15c to +35c / +85c / +15c to +35c time: 30 / 2 to 3 / 30 / 2 to 3 minutes 5 cycles reflow: at the recommended temperature profile manual soldering: 350c 5c for 5 seconds (note 3) 1. insulation resistance 500 m? min. 2. withstanding voltage no flashover or insulation breakdown 3. contact resistance 100 m? max. * including fpc and ffc conductor resistance 4. durability contact resistance: 100 m? max. no damage, cracks, or parts dislocation 5. vibration no electrical discontinuity of 1s or longer contact resistance: 100 m? max. no damage, cracks, or parts dislocation 6. shock no electrical discontinuity of 1s or longer contact resistance: 100 m? max. no damage, cracks, or parts dislocation 7. humidity (steady state) contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation 8. temperature cycle contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation 9. resistance to soldering heat no deformation of components affecting performance note1: when passing the current through all of the contacts, use 70% of the rated current. note2: includes temperature rise caused by current flow. note3: the term "storage" refers to products stored for a long period prior to mounting and use. the operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment o r during transportation after board mounting. note4: information contained in this catalog represents general requirements for this series. contact us for the drawings and specifications for a specific part number shown. ordering information materials series name : fh series no. : 34s blank : standard j: top contact, halogen-free (flame retardance ul94v-0). w : top contact, halogen-free (flame retardance ul94hb). r : bottom contact rj : bottom contact, halogen-free (flame retardance ul94v-0). 1 2 3 4 5 6 7 number of positions : 4 to 34 contact pitch : 0.5mm termination type sh : smt horizontal mounting type plating specifications (50)gold plating with nickel barrier lcp(8pos.) pa lcp phosphor bronze phosphor bronze fh34s series fh34sj series fh34sw series fh34sr series fh34srj series fh34s series fh34sj series fh34sr series fh34srj series fh34sw series fh34sj series fh34sr series color:beige color:gray color:black color:light brown color:black gold plating with nickel barrier pure tin reflow plating ul94v-0 ul94hb ul94v-0 ------- ------- insulator contacts metalfittings material finish remarks part fh 34s j - 30s - 0.5 sh ( 50 ) 1 2 4 5 3 6 7
580-1203-2-50 580-1205-8-50 580-1224-2-50 580-1204-5-50 580-1213-6-50 580-1206-0-50 580-1211-0-50 580-1217-7-50 580-1216-4-50 580-1228-3-50 580-1210-8-50 580-1212-3-50 580-1201-7-50 580-1208-6-50 580-1207-3-50 580-1237-4-50 580-1234-6-50 580-1235-9-50 580-1239-0-50 580-1225-5-50 580-1233-3-50 580-1240-9-50 580-1238-7-50 580-1236-1-50 580-1231-8-50 3 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors connector dimensions a** 10.1 (1.75) (3.8) 2.9 0.3 2.9 0.5 1 0.1 number of contacts (1.95) hrs mark cav no. number of contacts indicator b (c) d0.1 (0.15) a0.15 (0.15) 0.5 (3.2) 0.15 h h note 1 : the coplanarity of each terminal lead within specified dimension is 0.1 mm max. note 2 : packaged on tape and reel only. check packaging specification. note 3 : slight variations in color of the plastic compounds do not affect form, fit or function of the connector. note 4 : after reflow, the terminal plating may change color, however this does not represent a quality issue. tape and reel packaging (5,000 pieces/reel). order by number of reels. all dimensions: mm part number fh34s-4s-0.5sh(50) fh34s-6s-0.5sh(50) fh34s-7s-0.5sh(50) fh34s-8s-0.5sh(50) fh34s-11s-0.5sh(50) fh34s-14s-0.5sh(50) fh34s-16s-0.5sh(50) fh34s-20s-0.5sh(50) fh34s-22s-0.5sh(50) fh34s-23s-0.5sh(50) fh34s-24s-0.5sh(50) fh34s-26s-0.5sh(50) fh34s-30s-0.5sh(50) fh34s-32s-0.5sh(50) fh34s-34s-0.5sh(50) fh34sj-4s-0.5sh(50) fh34sj-6s-0.5sh(50) fh34sj-8s-0.5sh(50) fh34sj-30s-0.5sh(50) fh34sw-4s-0.5sh(50) fh34sw-12s-0.5sh(50) fh34sr-22s-0.5sh(50) fh34srj-4s-0.5sh(50) fh34srj-6s-0.5sh(50) fh34srj-8s-0.5sh(50) 4 6 7 8 11 14 16 20 22 23 24 26 30 32 34 4 6 8 30 4 12 22 4 6 8 4 5 5.5 6 7.5 9 10 12 13 13.5 14 15 17 18 19 4 5 6 17 4 8 13 4 5 6 1.5 2.5 3 3.5 5 6.5 7.5 9.5 10.5 11 11.5 12.5 14.5 15.5 16.5 1.5 2.5 3.5 14.5 1.5 5.5 10.5 1.5 2.5 3.5 2.53 3.53 4.03 4.53 6.03 7.53 8.57 10.57 11.57 12.07 12.57 13.57 15.57 16.53 17.53 2.53 3.53 4.53 15.57 2.53 6.53 11.57 2.53 3.53 4.53 3.38 4.38 4.88 5.38 6.88 8.38 9.38 11.38 12.38 12.88 13.38 14.38 16.38 17.38 18.38 3.38 4.38 5.38 16.38 3.38 7.38 12.38 3.38 4.38 5.38 cl no. number of contacts a b c d
2.5 3.5 4 4.5 6 7.5 8.5 10.5 11.5 12 12.5 13.5 15.5 16.5 17.5 2.5 3.5 4.5 15.5 2.5 6.5 11.5 2.5 3.5 4.5 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 4 0.650.03 (metal mask) (0.25) b 0.250.03 (metal mask) (0.25) (a) (2.9) e0.1 f0.1 0.80.05 3.30.05 (0.15) (0.15) (0.065) (0.185) number of contacts 0.5 0.80.05 0.30.05 recommended metal mask thickness: t=0.1 0.1 j j 1.50.3 2.5min(stiffener) h (uncover area) g0.05 b0.03 0.30.03 2-r0.2 0.50.07 0.50.03 0.30.03 recommended pcb mounting pattern and metal mask dimensions recommended fpc/ffc dimensions all dimensions: mm part number fh34s-4s-0.5sh(50) fh34s-6s-0.5sh(50) fh34s-7s-0.5sh(50) fh34s-8s-0.5sh(50) fh34s-11s-0.5sh(50) fh34s-14s-0.5sh(50) fh34s-16s-0.5sh(50) fh34s-20s-0.5sh(50) fh34s-22s-0.5sh(50) fh34s-23s-0.5sh(50) fh34s-24s-0.5sh(50) fh34s-26s-0.5sh(50) fh34s-30s-0.5sh(50) fh34s-32s-0.5sh(50) fh34s-34s-0.5sh(50) fh34sj-4s-0.5sh(50) fh34sj-6s-0.5sh(50) fh34sj-8s-0.5sh(50) fh34sj-30s-0.5sh(50) fh34sw-4s-0.5sh(50) fh34sw-12s-0.5sh(50) fh34sr-22s-0.5sh(50) fh34srj-4s-0.5sh(50) fh34srj-6s-0.5sh(50) fh34srj-8s-0.5sh(50) 580-1203-2-50 580-1205-8-50 580-1224-2-50 580-1204-5-50 580-1213-6-50 580-1206-0-50 580-1211-0-50 580-1217-7-50 580-1216-4-50 580-1228-3-50 580-1210-8-50 580-1212-3-50 580-1201-7-50 580-1208-6-50 580-1207-3-50 580-1237-4-50 580-1234-6-50 580-1235-9-50 580-1239-0-50 580-1225-5-50 580-1233-3-50 580-1240-9-50 580-1238-7-50 580-1236-1-50 580-1231-8-50 4 6 7 8 11 14 16 20 22 23 24 26 30 32 34 4 6 8 30 4 12 22 4 6 8 4 5 5.5 6 7.5 9 10 12 13 13.5 14 15 17 18 19 4 5 6 17 4 8 13 4 5 6 1.5 2.5 3 3.5 5 6.5 7.5 9.5 10.5 11 11.5 12.5 14.5 15.5 16.5 1.5 2.5 3.5 14.5 1.5 5.5 10.5 1.5 2.5 3.5 3.1 4.1 4.6 5.1 6.6 8.1 9.1 11.1 12.1 12.6 13.1 14.1 16.1 17.1 18.1 3.1 4.1 5.1 16.1 3.1 7.1 12.1 3.1 4.1 5.1 3.9 4.9 5.4 5.9 7.4 8.9 9.9 11.9 12.9 13.4 13.9 14.9 16.9 17.9 18.9 3.9 4.9 5.9 16.9 3.9 7.9 12.9 3.9 4.9 5.9 cl no. number of contacts a b e f g note 1 : stiffener dimension should be 2.5mm min., and h dimension should be 0.5mm for improved flexibility of fpc. note 2 : when using the fpc/ffc in fh34s or fh19sc connectors, the exposed area inserted in either connector is 2.5mm 0.3mm and the stiffener is 3.5mm min.
5 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors recommended fpc construction contact fpc manufacturer for specific details. 1. using single-sided fpc fpc : flexible printed circuit material name material material thickness (m) covering film layer cover adhesive polyimide 1 mil thick (25) (25) surface treatment 0.2m thick gold plated over 1 to 5m thick nickel underplating 3 copper foil base adhesive base film reinforcement material adhesive stiffener cu 1oz thermosetting adhesive polyimide 1 mil thick thermosetting adhesive polyimide 7 mil thick 35 25 25 35 175 total 298 3. using ffc ffc : flexible flat cable polyester film adhesive thermoplastic polyester (12) (30) 35 30 12 30 188 295 material name material material thickness (m) gold plated annealed copper foil adhesive polyester adhesive stiffener polyester polyester polyester total (25) (25) 2. using double-sided fpc * to prevent release of the fpc due to its bending, use of the double sided fpc with copper foil on the back side is not recommen ded. fpc : flexible printed circuit material name covering layer film cover adhesive material material thickness (m) polyimide 1 mil thick surface treatment 0.2m thick gold plated over 1 to 5m thick nickel underplating 3 through-hole copper copper foil base adhesive base film base adhesive cu cu 1/2oz thermosetting adhesive polyimide 1 mil thick 15 18 18 25 18 copper foil cover adhesive covering film layer reinforcement material adhesive stiffener cu 1/2oz thermosetting adhesive polyimide 1 mil thick thermosetting adhesive polyimide 4 mil thick (18) 25 25 50 100 total 297 1. this specification is a recommendation for the construction of the fh34s series fpc and ffc (t=0.3 0.03). 2. for details about the construction, please contact the fpc/ffc manufacturers. 4. precautions
fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 6 0 l0.3 1.750.1 flat surface, for placement with automatic equipment 80.1 20.15 40.1 m0.1 ?1.5 + 0 .1 unreeling direction (0.3) (p) (2.25) (3.2) (4) (1.95) ?1.5 +0.1 0 (1.95) (2.25) (0.3) flat surface, for placement with automatic equipment unreeling direction 1.7 +0.15 1.5 +0.1 (p) l0.3 m0.1 1.750.1 n0.1 0 0 end section mounting section embossed carrier tape lead section (400mm min.) top cover tape no connector inserted (10 pockets min.) no connector inserted (10 pockets min.) packaging specification embossed carrier tape dimensions (tape width 24mm max.) mc 6 -m . -m . -n 54 >:. -9@i%4 >:. reel dimensions embossed carrier tape dimensions (tape width of 32mm min.)
7 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors all dimensions: mm part number fh34s-4s-0.5sh(50) fh34s-6s-0.5sh(50) fh34s-7s-0.5sh(50) fh34s-8s-0.5sh(50) fh34s-11s-0.5sh(50) fh34s-14s-0.5sh(50) fh34s-16s-0.5sh(50) fh34s-20s-0.5sh(50) fh34s-22s-0.5sh(50) fh34s-23s-0.5sh(50) fh34s-24s-0.5sh(50) fh34s-26s-0.5sh(50) fh34s-30s-0.5sh(50) fh34s-32s-0.5sh(50) fh34s-34s-0.5sh(50) fh34sj-4s-0.5sh(50) fh34sj-6s-0.5sh(50) fh34sj-8s-0.5sh(50) fh34sj-30s-0.5sh(50) fh34sw-4s-0.5sh(50) fh34sw-12s-0.5sh(50) fh34sr-22s-0.5sh(50) fh34srj-4s-0.5sh(50) fh34srj-6s-0.5sh(50) fh34srj-8s-0.5sh(50) cl580-1203-2-50 cl580-1205-8-50 cl580-1224-2-50 cl580-1204-5-50 cl580-1213-6-50 cl580-1206-0-50 cl580-1211-0-50 cl580-1217-7-50 cl580-1216-4-50 cl580-1228-3-50 cl580-1210-8-50 cl580-1212-3-50 cl580-1201-7-50 cl580-1208-6-50 cl580-1207-3-50 cl580-1237-4-50 cl580-1234-6-50 cl580-1235-9-50 cl580-1239-0-50 cl580-1225-5-50 cl580-1233-3-50 cl580-1240-9-50 cl580-1238-7-50 cl580-1236-1-50 cl580-1231-8-50 4 6 7 8 11 14 16 20 22 23 24 26 30 32 34 4 6 8 30 4 12 22 4 6 8 cl no. number of contacts 16 16 16 16 16 24 24 24 24 24 24 24 32 32 32 16 16 16 32 16 24 24 16 16 16 7.5 7.5 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 14.2 14.2 14.2 7.5 7.5 7.5 14.2 7.5 11.5 11.5 7.5 7.5 7.5 28.4 28.4 28.4 28.4 4.3 5.3 5.8 6.3 7.8 9.3 10.3 12.3 13.3 13.8 14.3 15.3 17.3 18.3 19.3 4.3 5.3 6.3 17.3 4.3 8.3 13.3 4.3 5.3 6.3 17.4 17.4 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 33.4 33.4 33.4 17.4 17.4 17.4 33.4 17.4 25.4 25.4 17.4 17.4 17.4 21.4 21.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 37.4 21.4 21.4 21.4 37.4 21.4 29.4 29.4 21.4 21.4 21.4 l m n p q r tape and reel packaging (5,000 pieces/reel).
fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 8 max 250? start temperature(?) time (seconds) 25? (60 sec.) (60 sec.) 90 to 120 sec. preheating soldering 0 50 100 150 150? 200? 230? 200 250 hrs test condition solder method : reflow, ir/hot air environment : room air solder composition : paste, 96.5%sn/3.0%ag/0.5%cu (senju metal industry, co., ltd.'s part number: m705-221cm5-42-10.5) test board : glass epoxy 25mm40mm0.8mm thick land dimensions : 0.3mm0.8mm metal mask : 0.250.650.1mm thick the temperature profiles shown are based on the above conditions. in individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. consult your solder paste and equipment manufacturer for specific recommendations. temperature profile
9 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors operation and precautions exercise care when handling connectors. follow recommendations given below. 1. as delivered delivered with the actuator open. there is no need to operate the actuator prior to inserting the fpc/ffc. operation 2. fpc/ffc insertion (the top contact specification) insert the fpc/ffc with the conductive surfaces facing up. align the fpc/ffc straight with the connector and insert it firmly all the way. ? do not close the actuator without the fpc/fpc inserted. precautions ? the contacts are making connection with the fpc/ffc pads from the top. do not insert the fpc/ffc with the pads facing down. when inserting the fpc/ffc do not twist it. insert straight. improper insertion may cause deformation of the contacts and connection failures. ? be sure to insert the fpc/ffc when the actuator is fully open. fpc/ffc contact surfaces face up. 3. locking after fpc/ffc insertion, rotate the actuator down to a full stop, pushing it at the center. ? do not operate the actuator by only one end. open or close by pushing at the center. ? do not try to rotate the actuator past the fully open 90 position. this will damage the connector, preventing it from use. ? do not apply excessive force to the connector when the actuator is closed. rotate push at the center of the actuator. 4. fpc/ffc removal (lock release) carefully rotate the actuator up to 90, lifting it at the center. ? do not operate the actuator from one end only. ? the actuator opens only 90. do not attempt to open it past this angle or grasp it. ? during the opening of the actuator do not press it toward the connector body. rotate up at the center. raise lift at the center
fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 10 precautions at the design stage (1) route the fpc/ffc so that a direct pull force (2) make sure that there is enough space to insert/remove the fpc/ffc straight. (3) follow the recommendations given in this catalog in regard to mounting pattern, metal mask dimensions and fpc/ffc mating dimensions. (4) consult the manufacturer of the fpc/ffc for the details on the flexibility of the specific fpc/ffc. (5) when designing the board lay-out and spaces in the device assure that there is enough clearances for the actuator to fully open/close. when hand soldering: do not perform hand soldering with the fpc inserted in the connector. * do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. * do not use excessive amount of solder or flux compounds. operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. handling before mounting on pcb insertion of the fpc/ffc or operation of the actuator prior to mounting on the pcb is not recommended. pc board warpage minimize the warpage as much as possible. the connector are straight within 0.1 mm max. make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. forces on the board when braking the large pc board into individual boards exercise care not to damage the installed connectors. when attaching the boards or other components with the screws make sure that any stresses will not cause board deflections affecting the mounting areas of the connector. precautions when mounting connectors on the pcb connectors pcb
11 fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors notes :
fh34 ( s ) series 0.5 mm pitch, 1.0 mm above the board top and bottom contact, back-flip actuator flexible printed circuit & flexible flat cable zif connectors 12 the contents of this catalog are current as of date of 03/2012. contents are subject to change without notice for the purpose o f improvements. usa: hirose electric (u.s.a.), inc. san jose office 20400 stevens creek blvd., ste 250, cupertino, ca 95014 phone : +1-408-253-9640 fax : +1-408-253-9641 http://www.hiroseusa.com usa: hirose electric (u.s.a.), inc. headquarters 2688 westhills court, simi valley, ca 93065-6235 phone : +1-805-522-7958 fax : +1-805-522-3217 http://www.hiroseusa.com hong kong: hirose electric hongkong trading co., ltd. room 1001, west wing, tsim sha tsui centre, 66 mody road, tsim sha tsui east, kowloon, hong kong phone : +852-2803-5338 fax : +852-2591-6560 http://www.hirose-hongkong.com.hk china: hirose electric (shanghai) co., ltd. beijing branch a1001, ocean international center, building 56# east 4th ring middle road, chao yang district, beijing, 100025 phone : +86-10-5165-9332 fax : +86-10-5908-1381 http://www.hirose-china.com.cn taiwan: hirose electric taiwan co., ltd. 103 8f, no.87, zhengzhou rd., taipei phone : +886-2-2555-7377 fax : +886-2-2555-7350 http://www.hirose-taiwan.com.tw germany: hirose electric europe b.v. german branch herzog-carl-strasse 4 d-73760 ostfildern (scharnhauser park) phone : +49-711-4560-02-1 fax : +49-711-4560-02-299 http://www.hirose.de india: hirose electric singapore pte. ltd. bangalore liaison office unit no.03, ground floor, explorer building international tech park whitefield road, bangalore 560066 karnataka, india phone : +65-6324-6113 fax : +65-6324-6123 http://www.hirose-singapore.com.sg singapore: hirose electric singapore pte. ltd. 10 anson road #26-16 international plaza 079903 phone : +65-6324-6113 fax : + 65-6324-6123 http://www.hirose-singapore.com.sg the netherlands: hirose electric europe b.v. hogehillweg #8 1101 cc amsterdam z-o phone : +31-20-6557460 fax : +31-20-6557469 http://www.hiroseeurope.com united kingdom: hirose electric europe b.v. uk branch first floor, st andrews house, caldecotte lake business park, milton keynes mk7 8le phone : +44-1908-369060 fax : +44-1908-369078 http://www.hirose.co.uk usa: hirose electric (u.s.a.), inc. detroit office (automotive) 37677 professional center drive, suite #100c livonia, mi 48154 phone : +1-734-542-9963 fax : +1-734-542-9964 http://www.hiroseusa.com china: hirose electric (shanghai) co., ltd. 1601,henderson metropolitan,no.300 ,east nanjing road,huangpu district, shanghai,china 200001 phone : +86-21-6391-3355 fax : +86-21-6391-3335 http://www.hirose-china.com.cn china: hirose electric technologies (shenzhen) co., ltd. room 09-13, 19/f, office tower shun hing square, di wang commercial centre 5002, shennandong road, shenzhen city, guangdong province, 518008 phone : +86-755-8207-0851 fax : +86-755-8207-0873 http://www.hirose-china.com.cn korea: hirose korea co., ltd. 1261-10, jeoungwhang-dong, shihung-city, kyunggi-do 429-450 phone : +82-31-496-7000,7124 fax : +82-31-496-7100 http://www.hirose.co.kr 6-3,nakagawa chuoh-2-chome,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ?

▲Up To Search▲

Price & Availability of FH34SJ-30S-05SH50

	To Download FH34SJ-30S-05SH50 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .